Skip to product information
1 of 6

electrical center b2c

E5CC Replacement | TX6A 48x48 PID, 45x45 Cutout PID Temperature Controller

Regular price $47.00 USD
Regular price Sale price $47.00 USD
Sale Sold out
Shipping calculated at checkout.
Model NO. & Signal Output Type
Added ✓

The E5CC Is Obsolete — Here's the 45×45 mm Drop-In That Isn't

Intro block

Omron ended production of the E5CC series on 31 July 2022. Their published replacement is the E5CD — a better controller, but a newer and more expensive one, and it does not help if your machine is down today and the distributor shows no stock. The TX6A occupies the same 45×45 mm aperture, runs on the same 100–240 VAC supply, accepts the same thermocouple and RTD types, and is available from a single sample unit. For maintenance teams managing a fleet of E5CC-equipped machines, it is the lowest-friction way off an obsolete part number.

Why this page convertsObsolescence searches have the shortest path to purchase in this category. The visitor already knows the part number, already knows it is dead, and is comparingavailableoptions — not browsing. Every element on this page should answer “will it fit, and can I get it this week” rather than educate.

Three-way comparison: E5CC vs E5CD vs TX6A

Including Omron's own successor in the table is deliberate. It pre-empts the question every buyer asks, and it lets you win on the axes that matter to a maintenance budget rather than a specification sheet.

Parameter Omron E5CC (obsolete) Omron E5CD (OEM successor) YHKJ TX6A
Status EOL 2022-07-31 Current Current production
Frame / cutout 48×48 / 45×45 mm 48×48 / 45×45 mm 48×48 / 45×45 mm
Panel depth 60 mm; 73.1 mm with terminal cover approx. 60 mm class TBC — confirm against drawing
Supply 100–240 VAC 50/60 Hz; 24 VAC/VDC option 100–240 VAC; 24 VAC/VDC option 100–240 VAC std; 24 V as -LV
Display Dual 4-digit, PV + SV, 11-segment Dual, brighter white PV Dual 4-digit PV red / SV green + MV bar
Input Universal TC / RTD / analogue, ±0.2% FS Universal, faster 50 ms cycle K/J/T/R/S/B/E/N, Pt100/Cu50; 4–20 mA on AA320; accy TBC
Output Relay 250 VAC 3 A / voltage pulse for SSR / linear 4–20 mA Same families + event input, 2-prog PID Relay / SSR 12 V / 0–10 V / 4–20 mA
Comms RS-485 Modbus (E5CC-C / -R) RS-485 Modbus + EtherCAT/Cat/Net variants RS-485 Modbus RTU on “T” suffix
Approvals UL / cUL / CE / RoHS, UL508A panel-mount use UL / cUL / CE / RCM / KC Designed to UL 60730-1 / -2-9; UL Recognized, UL Listed TBC
Typical street price Discontinued, remaining stock at premium Higher than E5CC was Quote on request, samples from 1 pc
Availability None from Omron Distribution stock, model dependent Ex-stock, Yiwu CN warehouse

E5CC / E5CD data from Omron published documentation and distributor listings. Prices are indicative and vary by region and suffix. TX6A fields marked TBC must be completed from factory data before this page goes live.

Mapping the old ordering code

E5CC suffixes encode output configuration in positions most buyers no longer remember. Decode the old part first, then match on function — do not guess from the display.

Legacy E5CC function TX6A equivalent Note
Relay output, basic (CX / QX class) TX6-AK1220 Single alarm
Relay output, dual alarm TX6-AK1224 AL1 + AL2
Relay output + RS-485 TX6-AK120T Modbus RTU
Voltage-pulse output for external SSR TX6-AK1620 12 VDC SSR drive
SSR drive + communications TX6-AK220T Preferred for heated barrels, ovens
Linear 0–10 V output TX6-AK2520 Drives SCR trigger boards
Linear 4–20 mA output TX6-AK320 / AK320T “T” adds RS-485
24 VAC/VDC supply variant Add -LV Append to any part number above


Load sizing before you order

The single most common post-swap failure is putting a relay-output controller on a contactor coil or heater that exceeds its rating. Match the output family to the load, not to the old part number.

Heater load Recommended output Why
≤ 1.5 kW Relay (TX6-AK1220 / 1224 / 120T) In-built 250 VAC 3 A contact, direct switching
1.5 – 15 kW SSR drive + external SSR (TX6-AK1620 / 220T) Zero-cross SSR, no contact wear, high cycle rate
> 15 kW / three-phase 0–10 V (TX6-AK2520) + SCR trigger Phase-angle control of 3-phase banks
Inductive load (coil, solenoid, motor starter) Derate relay to ~50% or use SSR Inrush and back-EMF destroy relay contacts


Changeover procedure

Decode the E5CC suffix
Photograph the nameplate; the characters after the dash define output, alarm and supply. A wrong guess here is a wrong part.
Export the parameters
Photograph every setup-map page (level 1, 2, 3 and adjustment menus) — PID constants, alarm type, input shift, decimal point, PV bias. You will re-enter these by hand.
Confirm supply and depth
120 VAC is the norm on North American sites; the deep-terminal-cover depth of the E5CC was 73.1 mm. Measure what you actually have.
De-energise and re-terminate
E5CC and TX6A terminal assignments differ. Wire 1&2 supply / 3&4 input / 5&6 OUT1 / 7&8 OUT2 / A&B RS-485, then re-check with a meter before power-up.
Re-enter parameters and run AT
Set input type, range, decimal point, alarm mode and output family to match the exported values, then run auto-tuning with the load connected and the process at a safe temperature.
Re-point the HMI/SCADA tags
Modbus is standard but the register map is not shared. Budget for this step on any E5CC-C / E5CC-R installation.

FAQ

Is the Omron E5CC really discontinued?
Yes. Omron declared the E5CC series obsolete with an end-of-life date of 31 July 2022 and directs new designs to the E5CD. Remaining E5CC stock is held by distributors and typically trades at a premium. If a machine in your plant runs an E5CC, you are on a dead part number.
–
Can I put a TX6A in the same hole?
Yes. Both are 1/16 DIN: 48×48 mm face, 45×45 mm cutout, +0.6 mm tolerance. No panel modification. Check the free depth behind the panel against the TX6A outline drawing — the E5CC needed 60 mm, or 73.1 mm with the terminal cover fitted.
–
Do I need the same output type, or can I upgrade?
You must at minimum match the output family — relay, SSR drive, 0–10 V or 4–20 mA — because the field device downstream expects a specific signal. You can improve on it: many E5CC relay installations are better served by an SSR-drive TX6A plus an external solid-state relay, which removes the contact-wear failure mode entirely.
–
Will my thermocouple still read correctly?
Yes, provided you set the input type parameter to match the installed sensor. J, K, T, R, S, B, E and N thermocouples and Pt100/Cu50 RTDs are supported, with °C/°F selectable. Re-run auto-tuning afterwards — PID constants are load-specific and must not be copied across controllers.
–
What about the Omron E5CN and E5CZ?
Same 45×45 mm cutout, deeper bodies (the E5CN needs about 78 mm, or 91 mm with the cover). The TX6A swaps into those apertures as well, with the same part-number mapping by output family. If you maintain a mixed fleet of E5CC, E5CN and E5CZ, one TX6A spare covers all three.
–
Does the TX6A carry UL approval for a UL 508A panel?
The TX6A is designed to UL 60730-1 and UL 60730-2-9 and is supplied as a UL Recognized Component suitable for integration into a UL 508A control panel. UL Listed status as a standalone device, and cUL/CSA, are pending confirmation — do not represent the unit as UL Listed until the file number has been issued. Your panel shop can advise on the SCCR contribution.
–
How many do I have to buy?
One. Samples ship from a single piece so you can validate the swap on one machine before committing the fleet. Volume pricing applies from 50 pcs. Email info@electric-b2c.com with the nameplate photo and quantity.

 

Care Instructions

Variant image

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)